|
|
|
Lane Machine Programs
|
|
Thanks guys, I'll put these out and get people bowling on them and give you feedback. asap
|
|
Brunswick GS Pinsetters
|
|
I have never seen this. How does this happen and what causes it to happen?
|
|
Brunswick GS Pinsetters
|
|
I agree. But make sure that the tooth racks are in the correct position to begin with. I have found that if someone replaces ether the 3 or 10 pin tongs incorrectly, it throws the tooth racks out.
|
|
Pinspotters AMF
|
|
Good deal.Glad your spotting smoothly.
|
|
Pinsetters Brunswick
|
|
Pinsetter "individuality" creates more problems. Make them all the same!
|
|
Brunswick GS Pinsetters
|
|
Apparently there is a new mod for those pesky anchor nuts that break all the time. I have one on order.
|
|
Lane Maintenance
|
|
Break out the sunglasses....Nice!
|
|
Pinspotters AMF
|
|
We lowered all our head pin guides,and we run 21 pins.
|
|
Pinsetters Brunswick
|
|
The new 180 release spring that goes on the reset lever to the clutch release lever are made differant now...the eye is thicker. It works fine on the newer clutchrelease levers with the X-pin mounting spring, but it will bind if you try to tighten it
|
|
Pinsetters Brunswick
|
|
Where is H5 hook up in your box at? Check H1 and H4...you should have Input voltage. Check H1 and H2 and you should have 1/2 input voltage Same with H1 and H3 should be 1/2 input voltage....if not primary fuse is blown. If all checks good go to Lo
|
|
Pinspotters AMF
|
|
We have some belts like that they run ok. We just move things around if they rub. It depends where the spring is hooked onto I guess. I've seen two different places. As far as length goes, you may find you have less back end motor problems with a lon
|
|
Pinspotters AMF 82-30
|
|
i seriously need some help. I have a carpet which is determined to track to far to the ball door side. It is tracking so far that it is rubbing on the Ball door side rear roller housing and damaging the carpet. I have checked and replaced the followi
|
|
Pinsetters Brunswick
|
|
thanks for all the replies I was just curious, I dont mind getting deadwood been doing it since i got to this center. but just annoying when your fixing a machine then you have to go away from that machine to retrieve a deadwood, but all is good jus
|
|
Pro Shop Discussion
|
|
I have seen one of those determinators. If I didmore work that what I do I would have to have one. The bowler took the ball to a Pro shop that does way more work than I do today. He was impressed at the reaction this ball got also. He gave Storm a
|
|
Pinspotters AMF
|
|
I noticed the sides of the friction disk are finished differently....one has been 'cross sanded' so-to-speak.... Am I correct in assuming that this cross-sanded side goes against the clutch plate assembly....the part that only moves 360 degrees afte
|
|
Pinspotters AMF
|
|
Originally Posted By: ringing7i know changing the spot/respot cam is a pain but if all else fail then that has to be done. i have a distributor here that has a lot of washer and shims when i took over, after removing them i found out why, now have t
|
|
Lane Machine Programs
|
|
Try this post http://www.bowltech.com/content/btubb/ubbthreads.php?ubb=showflat&Number=408895#Post408895 or this one Century Silver Bullet (easy house shot) help http://www.bowltech.com/content/btubb/ubbthreads.php?ubb=showflat&Number=378748
|
|
Pinspotters AMF 82-30
|
|
I have the same problem, is there a book that describes the operation of the 82-20 or 30 pinsetter? I have a partial schematic, which describes part of the operation. I can, in due time, figure it out, but have three lanes down due to electrical pr
|
|
AMF Scoring Systems Discussion
|
|
The overlane cameras are a little tricky to adjust. They (mine anyway) sit higher above the lane than the underlane cams. I start with bubble in the level centered side to side but with the bubble almost entirely out of the circle towards the rear. T
|
|
Pinsetters Brunswick
|
|
what is causing the ball damage to increase? not being able to see that a ball has hung up, or the pin that would normally be ejected to the floor getting bounced back in to the machine? I have 50 lanes and not had any ball damage calls as a result o
|
|
Lane Machine Programs
|
|
id try it just like it is hpl lanes and wood lanes are virtually the same
|
|
Pinspotters AMF
|
|
Shaggy, CBS should provide you with a notebook full of parts catalogs and price lists of all the manufactures they distribute for. I just got a new one today. I think Western Pacific only supplies the price lists.
|
|
Lane Conditioning & Cleaning Machines Maintenance
|
|
Replaced my CVR with the non adjustable type. The reading of the CVR is always 26.2V. It is stopping consistently now... but similarly to cliff's story, now I can't get through the whole house. We are a 36 lane house and Last I checked a few months a
|
|
Lane Conditioning & Cleaning Machines Maintenance
|
|
Call you closest supplier to see if you can get one ASAP, maybe it is within driving distance. Tim
|
|
Pinspotters AMF
|
|
Originally Posted By: TABLEJAMWe were using the orange adjustable ones (#610-309-042), but started getting more and more defective ones so we changed over to the grey QAMF one, (#610-309-044), which wires up and is an exact replacement for the old Qu
|
